Janome · verified physical machine
Jump to: Proof E7
Identity verified · evidence for each owner answer
Identity verified · evidence for each answer
Check the conditions alongside each answer. Foot attachment, shank type and adapter requirements are separate; one does not establish universal accessory fit.
conditional
Use J-marked plastic bobbins for the horizontal hook; other bobbins, including pre-wound paper bobbins, may cause stitching problems or holder damage.
Source evidence · 1 unique proof passage: Profile Proof E1
conditional
Insert with thread running counterclockwise; hold the bobbin, thread the front notch and guide paths 1 then 2, confirming exit at the side notch, then replace the hook cover.
Source evidence · 1 unique proof passage: Profile Proof E2
conditional
Fine: Blue tip or Universal #9/65–11/75; medium Red tip, Purple tip or Universal #11/75–14/90; heavy Red tip, Purple tip or Universal #14/90–16/100.
Source evidence · 1 unique proof passage: Profile Proof E3
conditional
Insert flat side to rear, push to stopper pin and tighten clamp firmly with a screwdriver.
Source evidence · 1 unique proof passage: Profile Proof E4
conditional
Clean the hook area at least once a month.
Source evidence · 1 unique proof passage: Profile Proof E5
conditional
Remove needle plate, needle, presser foot, bobbin and holder; brush holder, feed dog and auto thread cutter, wipe the hook race, and replace holder with knob next to stopper; reassemble all removed components.
Source evidence · 1 unique proof passage: Profile Proof E5
What this passage supports
Fine | Lawn, Georgette, Tricot, Organza, Crepe | Silk #80-100, Cotton #80-100, Synthetic #80-100 | Blue tip needle, Universal needle #9/65-11/75 Medium | Sheeting, Jersey, Broadcloth, Fleece | Silk #50, Cotton #50-80, Synthetic #50-80 | Red tip needle, Purple tip needle, Universal needle #11/75-14/90 Heavy weight | Denim, Tweed, Coating, Quilting | Silk #30-50, Cotton #40-50, Synthetic #40-50 | Red tip needle, Purple tip needle, Universal needle #14/90-16/100
What this passage supports
Always make sure to press the lockout key to lockout the machine or turn the power switch off before inserting the bobbin. Place a bobbin in the bobbin holder with the thread running off counterclockwise as shown on the hook cover plate. Hold the bobbin with your fingertip so it does not rotate. Guide the thread into the front notch of the bobbin holder. Pull the thread to the left to pass it under the guide. Draw the thread to the left to pass it into the guide path marked “1”. Make sure that the thread comes out from the side notch of the bobbin holder. If the thread does not come out from the side notch, rethread from step 1. Continue to draw the thread along the guide path marked “2” and pull the thread to the right through the slit. The thread will be cut to a proper length and held in place. Set the left edge of the hook cover plate into opening. Push down the hook cover plate to fit in place. Unless otherwise noted, you can start sewing without drawing up the bobbin thread.
What this passage supports
Use the “J” plastic bobbins for horizontal hook (marked with “J”). Using other bobbins, such as pre-wound paper bobbins, may cause stitching problems and/ or damage to the bobbin holder.
What this passage supports
Always make sure to press the lockout key to lockout the machine or turn the power switch off before changing the needle. Insert a new needle into the needle clamp with the flat side of the needle to the rear. When inserting the needle into the needle clamp, push it up against the stopper pin and tighten the needle clamp screw firmly with a screwdriver. Never use a blunt needle.
What this passage supports
Turn the power switch off and unplug the machine before cleaning. Do not dismantle the machine in any way other than as explained in this section. Clean the hook area at least once a month. Remove the needle plate (refer to page 18). Remove the needle and presser foot. Take out the bobbin and bobbin holder. Clean the bobbin holder with a lint brush. Clean the feed dog and auto thread cutter device with the lint brush. Clean the hook race with a soft cloth. Insert the bobbin holder so that the knob fits next to the stopper in the hook race. Insert the bobbin. Attach the needle plate, presser foot and needle.
Cited machine facets
Identity families, physical traits, and OEM accessory groups stay separate. A group badge applies only to its named program and domains.
Catalog evidence coverage
Machine category:Not established in catalog evidence
Catalog core domains answered: None yet
Catalog domains with cited compatible items: None yet
Catalog unknown is not incompatible.Owner answers above are reviewed separately from catalog core-domain claims.
Specifications
Multiple cited representations for one field share one row. SewGraph preserves every value and exact proof passage; it does not guess which representation is “raw” or “normalized” when the public projection does not label that distinction.
Official source library
Open the exact OEM PDF page or captured HTML edition when a safe destination exists; otherwise SewGraph labels the OEM support-page fallback honestly.
accessory compatibility
Open official source destination · 1 unique proof passage: Proof E4
accessory catalog
Open official source destination · 1 unique proof passage: Proof E1
product page
Open official source destination · 1 unique proof passage: Proof E3
Evidence library
Every passage below says exactly what visible fact it proves. Repeated references to the same locator are counted once; identity evidence never counts as compatibility evidence.
Catalog compatibility proof passages: 0.The passages below support catalog identity and machine facts only; owner-answer sources are listed separately above.
What this passage proves
Computer models with AcuFeed system HMC7700QCP MC6600P MC6500P C (7 mm width) 7 mm High Yes and MC6500P 858 846F 846A 5300QDC 3160QDC 5270QDC 5120QDC DC4100 MC5200 MC4900QC MC4800 MC3500/3000 DC4030 Computer models (7 D 7 mm Low No 2160DC/2030DC DC7100/DC6030 mm/5 mm width) 5060QDC/DC3200 844 847 841 840 807 808 809 842 Top-loading (Horizontal 6019QC/6125QC EasyJeans 22 HD2200 Décor MyExcel4014 MS5027/MS5021 E Rotary Hook) models 6.5 mm Low No MyStyle 22 MyExcel 18/23 5124/5024/5018 4018/4023/4123 CS5031/SC5021 (6.5 mm width) 503 654 753 757 751 505 Sewist 625E Top-loading (Horizontal 525S/521 FD216/212/206 Jem Gold2 Jem Gold Harmony F Rotary Hook) models 5 mm Low No 725S/721 Sew Mini Platinum 4045/4052 (5 mm width) 507 508 661 660 502 Front loading L-392/372 L-393/373 423S/415/405 JR1012 3012/3016/3022 311 1580LX 920 G (Oscillating hook) 5 mm Low No models 731 721 303 743 306 311 748 304 990 ML634D/1110DX ML454D 90th 8002D 9102D ML644D ML213 DreamLock 70D ML744D H Overlockers Anniversary Sailing Line EzyLock604D 789 792 793 791 779 790 788 794 1000CPX 900CP CP3000P I CoverPro models 2000CPX 795 796 778 High speed straight 1600P HD9P J stitch models 767C 767F FM725 K Needle punching model 725 MB-4 MB-4S MB-7 L Multi-needle models 770 770 771 Combined overlock and 1200D 1100D M cover stitch models 797A 797C Embroidery & HMC15000 HMC14000 HMC12000 SKYLINE S9 CM17 N Sewing models 9 mm High Yes with Acufeed (9 mm) 862A 862F 859A 862SA 868A Embroidery & MC9900 O Sewing models 9 mm High No MC9850 (9 mm width) 861 Computer models SKYLINE S7 SKYLINE S6
What this passage proves
Computer models with AcuFeed system HMC7700QCP MC6600P MC6500P C (7 mm width) 7 mm High Yes and MC6500P 858 846F 846A 5300QDC 3160QDC 5270QDC 5120QDC DC4100 MC5200 MC4900QC MC4800 MC3500/3000 DC4030 Computer models (7 D 7 mm Low No 2160DC/2030DC DC7100/DC6030 mm/5 mm width) 5060QDC/DC3200 844 847 841 840 807 808 809 842 Top-loading (Horizontal 6019QC/6125QC EasyJeans 22 HD2200 Décor MyExcel4014 MS5027/MS5021 E Rotary Hook) models 6.5 mm Low No MyStyle 22 MyExcel 18/23 5124/5024/5018 4018/4023/4123 CS5031/SC5021 (6.5 mm width) 503 654 753 757 751 505 Sewist 625E Top-loading (Horizontal 525S/521 FD216/212/206 Jem Gold2 Jem Gold Harmony F Rotary Hook) models 5 mm Low No 725S/721 Sew Mini Platinum 4045/4052 (5 mm width) 507 508 661 660 502 Front loading L-392/372 L-393/373 423S/415/405 JR1012 3012/3016/3022 311 1580LX 920 G (Oscillating hook) 5 mm Low No models 731 721 303 743 306 311 748 304 990 ML634D/1110DX ML454D 90th 8002D 9102D ML644D ML213 DreamLock 70D ML744D H Overlockers Anniversary Sailing Line EzyLock604D 789 792 793 791 779 790 788 794 1000CPX 900CP CP3000P I CoverPro models 2000CPX 795 796 778 High speed straight 1600P HD9P J stitch models 767C 767F FM725 K Needle punching model 725 MB-4 MB-4S MB-7 L Multi-needle models 770 770 771 Combined overlock and 1200D 1100D M cover stitch models 797A 797C Embroidery & HMC15000 HMC14000 HMC12000 SKYLINE S9 CM17 N Sewing models 9 mm High Yes with Acufeed (9 mm) 862A 862F 859A 862SA 868A Embroidery & MC9900 O Sewing models 9 mm High No MC9850 (9 mm width) 861 Computer models SKYLINE S7 SKYLINE S6
What this passage proves
A modern sensibility meets the comforts of convenience. The Skyline S6 includes the features to take your sewing to a new level. A spacious bed provides room for larger quilting and home dec projects while its easy convenience features like Automatic Thread Cutter and Memorized Needle Up/Down will save you time and make your sewing easier. This computerized machine has top of the line features at a mid-level price. Take your sewing to new heights with the Skyline S6.
What this passage proves
SKYLINE S6
What this passage proves
Maximum Stitch Width 9mm
What this passage proves
SKYLINE S6
0 supported answers and 6 answers with conditions or remaining limits. Evidence coverage is not a probability of accuracy.
Public snapshot a1cc1aceef228fcf33329e37165ab888ce5b9fe3f13eb56967ae0fbf41d8d8a7
Catalog e156281c7d3048027b5ac89e7476be8f54dd5a9309505e96260b0455d3cd2a7e · exact native quotes only · dossier method sewgraph-model-dossier-v2