1200D

L. Needle Plate Setting Knob (Chaining finger) Your machine comes equipped with the rolled hem q plate. You can do all overlock stitches by engaging or disengaging the chaining finger. q Chaining finger To Engage (up) Pull the needle plate setting knob up. w Needle plate setting knobw To Disengage (down) Push the needle plate setting knob down.

Official source

Janome 1200D Professional instruction book (English, Polish, Spanish)

PDF page

32

Evidence path

Document → claim

Asset SHA-256

0617cf38fa38ef663c6ed6efbe0ff8c49be87fc89c802faea34918118941712c

Locator

49c5bff1758e4ee69d4758f84f393ab28ed722bdce555b41c1ca611adfd66409

H. Upper Knife To disengage the upper knife (down) Hand turn the handwheel to bring the needle bar to its highest position. Open the front and side covers. Push the upper knife release knob to the right and turn it towards you. NOTE: Do not allow the fabric edge to extend beyond the right side of the needle plate when sewing with the upper knife disengaged. (Example: any stitch that uses either R1 or R2 needle position.) To engage upper knife (up)

Official source

Janome 1200D Professional instruction book (English, Polish, Spanish)

PDF page

28

Evidence path

Document → claim

Asset SHA-256

0617cf38fa38ef663c6ed6efbe0ff8c49be87fc89c802faea34918118941712c

Locator

84207e5fc799887679e043b7fd4a8ca8d23caf477c0d6e571aef7fdc2525b33a

12. Upper looper 11 13. Lower looper 12 14. Chain looper

Official source

Janome 1200D Professional instruction book (English, Polish, Spanish)

PDF page

12

Evidence path

Document → claim

Asset SHA-256

0617cf38fa38ef663c6ed6efbe0ff8c49be87fc89c802faea34918118941712c

Locator

b926630741b30c0ac4506ab5b8762a472e529d4ab4e70d884a470bbaacfe41a1

Needles The machine is supplied with EL x 705 needles. This is an industrial type needle that ensures proper stitch formation at high speeds. The scarf (dent on needle back) is important because it allows the looper to come near the needle to catch the thread and form a stitch. EL x 705 needles are available in two sizes – 80/ 12 and 90/14.

Official source

Janome 1200D Professional instruction book (English, Polish, Spanish)

PDF page

34

Evidence path

Document → claim

Asset SHA-256

0617cf38fa38ef663c6ed6efbe0ff8c49be87fc89c802faea34918118941712c

Locator

e5b00ddf79002e777692542915d1d9ccb35f1ba46b7f76bb79bfdc6336b7815c

Remove the presser foot by pushing the lever on the back of the foot holder. Remove the needle plate by pushing down its release lever (a). Disengage the upper knife. (a) Use the brush to remove all lint and fiber accumulation. Apply a drop of oil above and below the oiling arrows. Oiling should be performed for every 8 hours of actual sewing operation. Reattach the needle plate by pressing down on its front section until it snaps onto the needle plate screw (b). To reattach the presser foot, place the foot underneath the foot holder and lower the presser bar. The foot will snap back into place.

Official source

Janome 1200D Professional instruction book (English, Polish, Spanish)

PDF page

106

Evidence path

Document → claim

Asset SHA-256

0617cf38fa38ef663c6ed6efbe0ff8c49be87fc89c802faea34918118941712c

Locator

a678f95f8f038c99990b004f376d5a4fe127abaad9fc9aacac9fd6939392aadc